View unanswered posts | View active topics It is currently Thu May 24, 2018 5:13 pm



Reply to topic  [ 6 posts ] 
 Don't start setup vSphere 4.1 on server with RTL8110/8169 
Author Message

Joined: Tue Jul 12, 2011 6:37 am
Posts: 4
Reply with quote
Post Don't start setup vSphere 4.1 on server with RTL8110/8169
Setup from iso don't start

"This system does not have a network interface card that is plugged in, or all network interface card are alredy claimed"

Sorry my bad english


Tue Jul 12, 2011 6:54 am
Profile

Joined: Wed Mar 18, 2009 1:32 pm
Posts: 455
Location: Sweden
Reply with quote
Post Re: Don't start setup vSphere 4.1 on server with RTL8110/816
Please post the hardware you are using.

_________________
Dovie'andi se tovya sagain,



Wed Jul 13, 2011 7:11 am
Profile WWW

Joined: Tue Jul 12, 2011 6:37 am
Posts: 4
Reply with quote
Post Re: Don't start setup vSphere 4.1 on server with RTL8110/816
I managed to install vSphere but there was a new problem, fixed hypervisor does not see the network card
I used http://code.google.com/p/mkesxiaio/
and viewtopic.php?f=12&t=3050&hilit=8169


lspci -nn
Code:
00:00.0 Host bridge [0600]: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub [8086:2770] (rev 02)
00:02.0 VGA compatible controller [0300]: Intel Corporation 82945G/GZ Integrated Graphics Controller [8086:2772] (rev 02)
00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 01)
00:1d.0 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 01)
00:1d.1 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 01)
00:1d.2 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 01)
00:1d.3 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 01)
00:1d.7 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 01)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev e1)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge [8086:27b8] (rev 01)
00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 01)
00:1f.2 IDE interface [0101]: Intel Corporation N10/ICH7 Family SATA IDE Controller [8086:27c0] (rev 01)
00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 01)
01:02.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105/VT6106S [Rhine-III] [1106:3106] (rev 8b)
01:03.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8110SC/8169SC Gigabit Ethernet [10ec:8167] (rev 10)


lscpi -vv
Code:
00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02)
   Subsystem: Foxconn International, Inc. Device 0ccb
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
   Latency: 0
   Capabilities: [e0] Vendor Specific Information: Len=09 <?>

00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller])
   Subsystem: Foxconn International, Inc. Device 0ccb
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Interrupt: pin A routed to IRQ 12
   Region 0: Memory at fdf00000 (32-bit, non-prefetchable) [size=512K]
   Region 1: I/O ports at ff00 [size=8]
   Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
   Region 3: Memory at fdf80000 (32-bit, non-prefetchable) [size=256K]
   Expansion ROM at <unassigned> [disabled]
   Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-
      Address: 00000000  Data: 0000
   Capabilities: [d0] Power Management version 2
      Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
      Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01)
   Subsystem: Foxconn International, Inc. Device 0ccb
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0, Cache Line Size: 32 bytes
   Interrupt: pin A routed to IRQ 16
   Region 0: Memory at fdff8000 (64-bit, non-prefetchable) [size=16K]
   Capabilities: [50] Power Management version 2
      Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
      Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
   Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+
      Address: 0000000000000000  Data: 0000
   Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
      DevCap:   MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
         ExtTag- RBE- FLReset-
      DevCtl:   Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
         RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
         MaxPayload 128 bytes, MaxReadReq 128 bytes
      DevSta:   CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
      LnkCap:   Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
         ClockPM- Surprise- LLActRep- BwNot-
      LnkCtl:   ASPM Disabled; Disabled- Retrain- CommClk-
         ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
      LnkSta:   Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
   Capabilities: [100 v1] Virtual Channel
      Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
      Arb:   Fixed- WRR32- WRR64- WRR128-
      Ctrl:   ArbSelect=Fixed
      Status:   InProgress-
      VC0:   Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
         Arb:   Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
         Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=01
         Status:   NegoPending- InProgress-
      VC1:   Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
         Arb:   Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
         Ctrl:   Enable+ ID=1 ArbSelect=Fixed TC/VC=80
         Status:   NegoPending- InProgress-
   Capabilities: [130 v1] Root Complex Link
      Desc:   PortNumber=0f ComponentID=02 EltType=Config
      Link0:   Desc:   TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+
         Addr:   00000000fed1c000
   Kernel driver in use: HDA Intel
   Kernel modules: snd-hda-intel

00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI])
   Subsystem: Foxconn International, Inc. Device 0ccb
   Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Interrupt: pin A routed to IRQ 23
   Region 4: I/O ports at fe00 [size=32]
   Kernel driver in use: uhci_hcd
   Kernel modules: uhci-hcd

00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI])
   Subsystem: Foxconn International, Inc. Device 0ccb
   Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Interrupt: pin B routed to IRQ 19
   Region 4: I/O ports at fd00 [size=32]
   Kernel driver in use: uhci_hcd
   Kernel modules: uhci-hcd

00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI])
   Subsystem: Foxconn International, Inc. Device 0ccb
   Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Interrupt: pin C routed to IRQ 18
   Region 4: I/O ports at fc00 [size=32]
   Kernel driver in use: uhci_hcd
   Kernel modules: uhci-hcd

00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI])
   Subsystem: Foxconn International, Inc. Device 0ccb
   Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Interrupt: pin D routed to IRQ 16
   Region 4: I/O ports at fb00 [size=32]
   Kernel driver in use: uhci_hcd
   Kernel modules: uhci-hcd

00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI])
   Subsystem: Foxconn International, Inc. Device 0ccb
   Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Interrupt: pin A routed to IRQ 23
   Region 0: Memory at fdfff000 (32-bit, non-prefetchable) [size=1K]
   Capabilities: [50] Power Management version 2
      Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
      Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
   Kernel driver in use: ehci_hcd
   Kernel modules: ehci-hcd

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode])
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
   I/O behind bridge: 0000e000-0000efff
   Memory behind bridge: fdd00000-fddfffff
   Prefetchable memory behind bridge: 00000000fde00000-00000000fdefffff
   Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
   BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
      PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
   Capabilities: [50] Subsystem: Intel Corporation 82801 PCI Bridge

00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
   Subsystem: Foxconn International, Inc. Device 0ccb
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Capabilities: [e0] Vendor Specific Information: Len=0c <?>

00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP])
   Subsystem: Foxconn International, Inc. Device 0ccb
   Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Interrupt: pin A routed to IRQ 18
   Region 0: I/O ports at 01f0 [size=8]
   Region 1: I/O ports at 03f4 [size=1]
   Region 2: I/O ports at 0170 [size=8]
   Region 3: I/O ports at 0374 [size=1]
   Region 4: I/O ports at fa00 [size=16]
   Kernel driver in use: ata_piix
   Kernel modules: ata_piix

00:1f.2 IDE interface: Intel Corporation N10/ICH7 Family SATA IDE Controller (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])
   Subsystem: Foxconn International, Inc. Device 0ccb
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 0
   Interrupt: pin B routed to IRQ 19
   Region 0: I/O ports at f900 [size=8]
   Region 1: I/O ports at f800 [size=4]
   Region 2: I/O ports at f700 [size=8]
   Region 3: I/O ports at f600 [size=4]
   Region 4: I/O ports at f500 [size=16]
   Region 5: Memory at fdffe000 (32-bit, non-prefetchable) [size=1K]
   Capabilities: [70] Power Management version 2
      Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
      Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
   Kernel driver in use: ata_piix
   Kernel modules: ata_piix

00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 01)
   Subsystem: Foxconn International, Inc. Device 0ccb
   Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Interrupt: pin B routed to IRQ 11
   Region 4: I/O ports at 0500 [size=32]

01:02.0 Ethernet controller: VIA Technologies, Inc. VT6105/VT6106S [Rhine-III] (rev 8b)
   Subsystem: D-Link System Inc Device 1405
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 32 (750ns min, 2000ns max), Cache Line Size: 32 bytes
   Interrupt: pin A routed to IRQ 17
   Region 0: I/O ports at ee00 [size=256]
   Region 1: Memory at fddff000 (32-bit, non-prefetchable) [size=256]
   Capabilities: [44] Power Management version 2
      Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
      Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
   Kernel driver in use: via-rhine
   Kernel modules: via-rhine

01:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8110SC/8169SC Gigabit Ethernet (rev 10)
   Subsystem: Foxconn International, Inc. Device 0ccb
   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
   Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
   Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
   Interrupt: pin A routed to IRQ 16
   Region 0: I/O ports at ec00 [size=256]
   Region 1: Memory at fddfe000 (32-bit, non-prefetchable) [size=256]
   [virtual] Expansion ROM at fde00000 [disabled] [size=128K]
   Capabilities: [dc] Power Management version 2
      Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
      Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
   Kernel driver in use: r8169
   Kernel modules: r8169



Thu Jul 14, 2011 4:10 am
Profile

Joined: Tue Jul 12, 2011 6:37 am
Posts: 4
Reply with quote
Post Re: Don't start setup vSphere 4.1 on server with RTL8110/816
Information collect from gentoo live cd


Thu Jul 14, 2011 4:11 am
Profile
Site Admin

Joined: Mon Mar 16, 2009 10:13 pm
Posts: 3880
Reply with quote
Post Re: Don't start setup vSphere 4.1 on server with RTL8110/816
Sorry for the delay in replying (I'm just getting back from vacation).

How have you had out with this?

_________________
Dave Mishchenko
VMware vExpert 2009-2013
Image
Now available - VMware ESXi: Planning, Implementation, and Security
Also available - vSphere Quick Start Guide


Mon Jul 25, 2011 8:47 pm
Profile

Joined: Tue Jul 12, 2011 6:37 am
Posts: 4
Reply with quote
Post Re: Don't start setup vSphere 4.1 on server with RTL8110/816
We have solved the problem for this we need the 2 files and oem.tgz oem2.tgz
isolinux.cfg
append vmkboot.gz ks = usb --- vmkernel.gz --- sys.vgz --- cim.vgz --- ienviron.vgz --- install.vgz --- oem.tgz

and pots inside your installation on the second and third fi trazdele need to change boot.cfg
modules = kz --- sz --- cz --- oem.tgz --- license.tgz --- mz --- oem2.tgz --- state.tgz --- vpxa.vgz

and of course, copy the file oem2.tgz


The original post in Russian that helped me
http://www.kharkovforum.com/showpost.ph ... ostcount=4


Thu Aug 11, 2011 3:18 am
Profile
Display posts from previous:  Sort by  
Reply to topic   [ 6 posts ] 

Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.
Designed by STSoftware for PTF.